GREAT PLAINS 3S-3000HD Operator'S Manual Download Page 21

Page: 21 / 116

Great Plains Manufacturing, Inc.

Table of Contents Index

Preparation and Setup

2019-03-12

Table of Contents Index

195-068M

Electrical Connections

Refer to Figure 7

Plug drill electrical lead into tractor seven-pin connector.

If your tractor is not equipped with a seven-pin

connector, contact your dealer for installation.

FigureSpacer

Refer to Figure 8

If the drill is equipped with the optional shaft monitor,

mate the connector for the cab display.
See “

Shaft Monitor

” on page 93 for ordering

information.

FigureSpacer

Refer to Figure 9

If the drill is equipped with the point row option, mate the

connector for the cab control.
See “

Point Row Clutch

” on page 92 for ordering

information.

FigureSpacer

Figure 7

Lighting Connector

26467

FigureSpacer

Figure 8

Shaft Monitor Connector

34222

FigureSpacer

Figure 9

Point-Row Connector

26469

Summary of Contents for 3S-3000HD





















































































































Search results

Summary of Contents for 3S-3000HD

Reviews:

Brands by name

Popular brands

GREAT PLAINS 3S-3000HD, Operator'S Manual

Search results

Summary of Contents for 3S-3000HD

Reviews:

Brands by name

Popular brands