manualshive.com logo in svg

Gravely PM320, Owner/Operator And Parts Manual, Page: 4 / 30

Share
Download
Gravely PM320 Owner/Operator And Parts Manual Download Page 4

4

SAFETY DECALS AND LOCATIONS

ALWAYS replace missing or damaged Safety Decals. Refer 
to Figure 2 for Safety Decal locations.

1. 

DANGER! ROTATING PARTS

Always keep feet and hands away from rotating 
parts.

Always stand clear of discharge area. Do not 
direct discharge toward other people.

Keep people away from unit while operating.

Shut off engine, remove key, read manual before 
you adjust or repair unit.

NO STEP! Always keep feet away from rotating 
parts.

2. WARNING! 

Do not operate mower unless guards are in operating 
position or bagger is attached.

Always stand clear of discharge area.

Do not operate mower unless bagger is attached 
or guards are in operating position.

SAFETY RULES

Read, understand, and follow all safety practices in 
Owner/Operator Manual before beginning assembly. Failure 
to follow instructions could result in personal injury and/or 
damage to unit.

ALWAYS remove key and/or wire from spark plug before 
assembly. Unintentional engine start up can cause death or 
serious injury.

Complete a walk around inspection of unit and work area to 
understand:

  • Work area   • Your unit   • All safety decals

Determine which attachments are needed and can be used 
safely.

DANGE R /PELIGRO

07731400D

DANGE R /PELIGRO

07731400D

WARNING/A VERTISSEMENT/ADVERTENCIA

Do not operate mo wer
unless guards are in
operating position or
b agg er is attached.

Ne jamais utiliser
la tondeuse sans
protecteur sur le
canal d'ejection ou
sans le bac monte .

No operar segadora  a
m enos que las defensas
esten en posicion de
operacion o el
recogedor este fijo .

07742300B

 Figure 2

OF3422

1

2

1

OL3030

OL0910

OL3292

OL4010

OL4420

OL4430

OL3320

Summary of Contents for PM320































Reviews:

No comments