background image

GRAUPNER/SJ GmbH   D-73230 KIRCHHEIM/TECK   GERMANY 

Modifications reserved. No liability for printing errors.  

 

                03/2013 

10

 

Don’t operate your model aeroplane in the vicinity of overhead power cables, industrial sites, residential 
areas, public roads, school playgrounds or sports fields etc. 

Pre-flight checks 

Check that the radio control system works correctly and at full range before every flight: switch on the 
transmitter and receiving system, and ensure that all the control surfaces work smoothly, and deflect in 
the correct “sense” in relation to the stick movements. 
If you are a beginner to this type of model flying, we recommend that you enlist an experienced model 
pilot to help you check and test-fly the model. 
 

Please don’t ignore our warnings. They refer to hazardous materials and processes which, if ignored, can 
result in fatal injury or serious damage to property. 

 
If you are to fly your model safely and avoid problems, it is essential that you are aware of its position 
and attitude throughout each flight - so don’t let it fly too far away. If you detect a control problem or 
interference during a flight, immediately land the model to prevent a potential accident. Model aeroplanes 
must always give way to full-size aircraft. Take-off and landing strips should be kept free of people and 
other obstacles. 
 
Your RC system can only work reliably if the batteries are kept fully charged. 
Never use hot, faulty or damaged batteries. It is important to observe the instructions supplied by the 
battery manufacturer. 
 
Manufacturer’s declaration: 
If material defects or manufacturing faults should arise in a product distributed by us in the Federal 
Republic of Germany and purchased by a consumer (§ 13 BGB), we, Graupner/SJ GmbH, D-73230 
Kirchheim/Teck, Germany, acknowledge the obligation to correct those defects within the limitations 
described below. 
The consumer is not entitled to exploit this manufacturer’s declaration if the failure in the usability of the 
product is due to natural wear, use under competition conditions, incompetent or improper use (including 
incorrect installation) or external influences. 
This manufacturer’s declaration does not affect the consumer’s legal or contractual rights regarding 
defects arising from the purchase contract between the consumer and the vendor (dealer). 
 
Extent of the guarantee 
If a claim is made under guarantee, we undertake at our discretion to repair or replace the defective 
goods. We will not consider supplementary claims, especially for reimbursement of costs relating to the 
defect (e.g. installation / removal costs) and compensation for consequent damages unless they are 
allowed by statute. This does not affect claims based on legal regulations, especially according to 
product liability law. 
 
Guarantee requirements 
The purchaser is required to make the guarantee claim in writing, and must enclose original proof of 
purchase (e.g. invoice, receipt, delivery note) and this guarantee card. The purchaser must send the 
defective goods to us at his own cost, using the address stated above. 
The purchaser should state the material defect or manufacturing fault, or the symptoms of the fault, in as 
accurate a manner as possible, so that we can check if our guarantee obligation is applicable. 
The goods are transported from the consumer to us and from us to the consumer at the risk of the 
consumer. 
 
Duration of validity 
This declaration only applies to claims made to us during the claim period as stated in this declaration. 
The claim period is 24 months from the date of purchase of the product by the consumer from a dealer in 
the Federal Republic of Germany (purchase date). If a defect arises after the end of the claim period, or if 
the evidence or documents required according to this declaration in order to make the claim valid are not 
presented until after this period, then the consumer forfeits any rights or claims from this declaration. 
 
Limitation by lapse of time 
If we do not acknowledge the validity of a claim based on this declaration within the claim period, all 
claims based on this declaration are barred by the statute of limitations after six months from the time of 
implementation; however, this cannot occur before the end of the claim period. 
 
Applicable law 
This declaration, and the claims, rights and obligations arising from it, are based exclusively on the 
pertinent German Law, excluding the norms of international private law, and excluding UN retail law. 

Summary of Contents for DANDY











Reviews: