background image

GRAUPNER/SJ GmbH   D-73230 KIRCHHEIM/TECK   GERMANY 

Modifications reserved. No liability for printing errors. 

3/2013 

 

14

 - 

Pre-flight checks 

Check  that  the  radio  control  system  works  correctly  and  at  full  range  before  every  flight:  switch  on  the 
transmitter and receiving system, and ensure that all the control surfaces work smoothly, and deflect in 
the correct “sense” in relation to the stick movements. 
If  you  are  a  beginner  to  this  type  of  model  flying,  we  recommend  that  you  enlist  an  experienced  model 
pilot to help you check and test-fly the model. 
 

Please don’t ignore our warnings. They refer to hazardous materials and processes which, if ignored, can 
result in fatal injury or serious damage to property. 

 
If  you  are  to  fly  your  model  safely  and  avoid  problems,  it  is  essential  that  you  are  aware  of  its  position 
and  attitude  throughout  each  flight  -  so  don’t  let  it  fly  too  far  away.  If  you  detect  a  control  problem  or 
interference during a flight, immediately land the model to prevent a potential accident. Model aeroplanes 
must always  give way to full-size aircraft. Take-off and landing strips should be kept free of people and 
other obstacles. 
 
Your RC system can only work reliably if the batteries are kept fully charged. 
Never  use  hot,  faulty  or  damaged  batteries.  It  is  important  to  observe  the  instructions  supplied  by  the 
battery manufacturer. 
 
Manufacturer’s declaration: 
If  material  defects  or  manufacturing  faults  should  arise  in  a  product  distributed  by  us  in  the  Federal 
Republic  of  Germany  and  purchased  by  a  consumer  (§  13  BGB),  we,  Graupner/SJ  GmbH,  D-73230 
Kirchheim/Teck,  Germany,  acknowledge  the  obligation  to  correct  those  defects  within  the  limitations 
described below. 
The consumer is not entitled to exploit this manufacturer’s declaration if the failure in the usability of the 
product is due to natural wear, use under competition conditions, incompetent or improper use (including 
incorrect installation) or external influences. 
This  manufacturer’s  declaration  does  not  affect  the  consumer’s  legal  or  contractual  rights  regarding 
defects arising from the purchase contract between the consumer and the vendor (dealer). 
 
Extent of the guarantee 
If  a  claim  is  made  under  guarantee,  we  undertake  at  our  discretion  to  repair  or  replace  the  defective 
goods. We will not consider supplementary claims, especially for reimbursement of costs relating to the 
defect  (e.g.  installation  /  removal  costs)  and  compensation  for  consequent  damages  unless  they  are 
allowed  by  statute.  This  does  not  affect  claims  based  on  legal  regulations,  especially  according  to 
product liability law. 
 
Guarantee requirements 
The  purchaser  is  required  to  make  the  guarantee  claim  in  writing,  and  must  enclose  original  proof  of 
purchase  (e.g.  invoice,  receipt,  delivery  note)  and  this  guarantee  card.  The  purchaser  must  send  the 
defective goods to us at his own cost, using the address stated above. 
The purchaser should state the material defect or manufacturing fault, or the symptoms of the fault, in as 
accurate a manner as possible, so that we can check if our guarantee obligation is applicable. 
The  goods  are  transported  from  the  consumer  to  us  and  from  us  to  the  consumer  at  the  risk  of  the 
consumer. 
 
Duration of validity 
This declaration only applies to claims made to us during the claim period as stated in this declaration. 
The claim period is 24 months from the date of purchase of the product by the consumer from a dealer in 
the Federal Republic of Germany (purchase date). If a defect arises after the end of the claim period, or if 
the evidence or documents required according to this declaration in order to make the claim valid are not 
presented until after this period, then the consumer forfeits any rights or claims from this declaration. 
 
Limitation by lapse of time 
If  we  do  not  acknowledge  the  validity  of  a  claim  based  on  this  declaration  within  the  claim  period,  all 
claims based on this declaration are barred by the statute of limitations after six months from the time of 
implementation; however, this cannot occur before the end of the claim period. 
 
Applicable law 
This  declaration,  and  the  claims,  rights  and  obligations  arising  from  it,  are  based  exclusively  on  the 
pertinent German Law, excluding the norms of international private law, and excluding UN retail law. 
 
 

Summary of Contents for 9547















Reviews: