GRASS VALLEY CR6400 Series User Manual Download Page 48

Page: 48 / 68

Technical Details

Physical Specifications

Physical Specifications

CR6400 Router Specifications

CP6464 Control Panel Specifications

Specification

Detail

Dimensions Height:

3.47”

(88.1mm),

fits EIA 2 RU (3.50” or 88.9mm),

Width: 19.0” (482.6mm).

Depth

10.18 ± 0.01” (258.6 mm), enclosure.

10.75” (273.1 mm) from front of rack to extended ground screw

Weight

11.8 lb (5.35 kg) with no I/O cards, without control panel.

15.3 lb (6.94 kg) with 4 I/O cards, without control panel.

Connectors

Power: 2 connectors. See the drawing under

Power Specifications

page 35.

Ethernet: 1 connector , 10/100BaseT, RJ-45 jack.

Serial: 1 connector, 9-pin D type, usage determined by software, SMPTE
207M.

Video reference: 2 connectors, BNC, 75

Two 2×60 connectors for optional control panel.

Removable module

4 I/O card slots at rear

1 crosspoint card slot at rear

1 control card slot at rear

1 fan module removable at the front

I/O module types

SDI. AES

Grounding terminal

Copper, accepts 14–6 AWG.

Specification

Detail

Dimensions Height:

3.41”

(86.6mm),

Width: 17.62” (447.5mm).

Depth 0.50”

(12.7mm)

enclosure,

0.82” (20.8mm) overall.

Weight

1.43 lb (0.65 kg).

Connectors

One 2×60 connector to the CR6400

Summary of Contents for CR6400 Series





































































Search results

Summary of Contents for CR6400 Series

Reviews:

Related manuals for CR6400 Series

Brands by name

Popular brands

GRASS VALLEY CR6400 Series, User Manual

Search results

Summary of Contents for CR6400 Series

Reviews:

Related manuals for CR6400 Series

Brands by name

Popular brands