GRASS VALLEY CR6400 Series User Manual Download Page 23 | Manualshive

Page: 23 / 68

background image

13

CR6400

User’s Guide

Pressing the destination mode button makes the selection buttons (or I/O buttons) turn
amber (high- or low-tally) In destination mode, the selection buttons select destinations.

Other function buttons are reserved for future use.

•

Each button has a clear plastic cap that can be easily removed to accommodate customer-
defined button legends.

•

Two LEDs indicate whether the power supplies of the router on which the control panel is
mounted are connected and functioning.

•

An LED indicates whether the router has reference. Another LED provides fan status.

•

A control panel mounts easily and quickly on the router with two knurled screws and electri-
cal connectors. The CR6400 routers have two connectors. The CP6464 presently has one
connector that mates to one of the connectors on the router.

«
...
21
22
23
24
25
...
»

Summary of Contents for CR6400 Series





































































Reviews:

No comments

Related manuals for CR6400 Series

Brand: D-Link Pages: 32

Brand: D-Link Pages: 6

Brand: D-Link Pages: 221

ShareCenter Pro DNS-1200-05

Brand: D-Link Pages: 68

Express Ethernetwork DI-707P

Brand: D-Link Pages: 14

Brand: Magnat Audio Pages: 2

DGE-560T - Gigabit PCI-Express SNMP VLAN Flow Control Network...

Brand: D-Link Pages: 53

Brand: Lancom Pages: 70

Brand: Patton electronics Pages: 12

NSLU2 - Network Storage Link NAS Server

Brand: Linksys Pages: 64

Brand: TRENDnet Pages: 62

Brand: Juniper Pages: 7

SABVISION NVR32

Brand: SAB Pages: 29

Elinx ESW200 Series

Brand: B&B Electronics Pages: 20

SRA311-008P8 Series

Brand: Divio Pages: 4

ExpressBox2 EB2

Brand: Magma Pages: 74

Compact NVR-AS 4000

Brand: IndigoVision Pages: 38

Brand: Federal Signal Corporation Pages: 49

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands