background image

 

 

 

PHOTOVOLTAIC MODULES SAFETY 

AND INSTALLATION MANUAL Rev. M 

VALID IN NORTH AMERICA ONLY 

Valid from February 2011 

1305 South Bertelsen Road, Eugene, Oregon 97402, USA 

www.grapesolar.com 

Tel: 1-877-264-1014 (toll free), 1-541-349-9000, Fax: 1-541-343-9000 

 

 

 

 

I.

 

  GENERAL INFORMATION 

1.

 

  Grape Solar photovoltaic (PV) modules are designed to produce DC electrical energy from sunlight.   

2.

 

  This manual contains important safety and installation information of Grape Solar PV modules. All 

safety and installation instructions described in this manual should be thoroughly understood before 
installing, operating and maintaining the PV system.   

3.

 

  Working on a PV system requires specialized knowledge, and must be performed by appropriately 

qualified and authorized personnel only.   

4.

 

  Grape Solar PV modules are subject to operate at ambient temperatures within the range -40°C to 

+85°C (-40°F to +185°F). 

5.

 

  PV modules are intended for outdoor, land-based applications only. 

6.

 

  Rated power output specification of Grape Solar PV modules are made at the Standard Test Condition 

(STC), which is 1000W/m

2

 irradiance, 1.5 Air Mass (AM), and 25°C (77ºF) cell temperature. 

However PV modules can produce voltage at as little as 5% of full sunlight, either connected or not 
connected to an electrical circuit or load.   

7.

 

  Electrical current and power generated by PV module increases with light intensity and higher power 

output than the rated specifications can be achieved at colder temperatures. 

8.

 

  Reflection from snow, water or other surfaces can increase light intensity, and therefore increase the 

current and power generated by the module. 

9.

 

  Do not artificially concentrate light on the module. Concentrating light on the module may result in 

damage to the module and malfunction of the whole PV system. 

10.

 

Follow all safety precautions of other equipments and components used in the PV system. 

11.

 

Retain this manual for future reference. 

12.

 

Grape Solar recommends that the customer makes a note of the serial numbers of modules in order to 
keep a record of the system. 

Summary of Contents for GS-S-150-SF














Reviews: