background image

16

LOCATION

 

CAUTIONS: 

n

 

Please keep away from hot surfaces, dusty and dirty areas,  
high temperature and high humidity.

 

n

 

Do not expose the projector to high wind or high-powered  
indoor fans.

n

 

Do not dismantle

REPAIRS

Please do not dismantle the screws of the projector lift.  
Should this product require repaired, please contact our  
company or dealers.

TROUBLESHOOTING

The Grandview Projector Lift can be used for years, with most problems being resolved 
inexpensively. If problems occur, please refer to list below for some common solutions.  
If problems continue, contact an authorized agent of Grandview or call the following 
service number: 1800 685 487

Reason

Solution

Projector Lift 
does not respond 
to any operation

Battery has not been installed 
correctly or is flat

Check that the batteries are 
installed correctly – refer to the 
manual. If flat, replace batteries.

Power disconnection

Check that the power is 
connected – refer to the manual.

THREE-YEAR WARRANTY

Grandview provides a three-year warranty for projector lifts. The warranty includes 
replacement of spare parts where problems occur during correct operation. 
Not included in the warranty are operating the projector lift incorrectly or uninstalling  
of the projector lift by a non-qualified person. 

NOTE:

 You should contact Grandview or an appointed service centre for repairs.

Summary of Contents for GRPL 1000





















Reviews: