background image

6

7

 

Angle adjuster 

Tighten the screws

projector

 

mounting Bracket

Screw

 

rod

Grille ceiling

Concrete base

screw nut

Concrete base

screw nut

Cushion

For the convenience of installation, the side plates of the cage can be removed first. After the installation is 

completed, the installer can stand in the cage and reinstall the side panels. At this time, the side panels must 

be turned over and installed.

If it is necessary to adjust the limit height due to the installation environment or the limitations of the site, it 

must be adjusted by a special technician or call after-sales.

1. Lower the bamboo joint of the lift to the height suitable for the installer to install the projector, and remove 

the mounting feet on the bamboo joint.

2. After the mounting feet are fixed on the projector, re-attach the projector and the mounting feet to the angle 

adjuster and tighten the screws.

(Note: Be sure to confirm that the screws are securely locked, be 

careful to prevent the projector from accidentally falling!)

Projector installation

3.After checking that the tapping screw is fixed, install the screw rod

 

and fix it. (In order to

 make the screw rod easier to pass through the lifter, we recommend that the end of the 

screw rod be tapered, and the length between each two lead rods can differ by 10-20mm.

recommended to sharpen the end of the screw into

 a taper that makes it easier to pass through the 

screw hole of the lift

4

.

Lift the lifter to the height of the installation position by using the lifting equipment, and

 pass the screw rod through the four holes of the lifter. Adjust the height of the lifter with the

 

screw nut so that it is flush with the height of the ceiling layer. Remove the

 

excess screw

 

rod

.

Please note that you must touch the upper limit switch to stop the projector lift from rising!

The level above the electric lift must be adjusted to the level, Tilting can cause the electric hanger to 

malfunction.

M10 rod x4

Grille ceiling

make the decorative frame fils on the celing layer

5.install the decorative frame so that the decorative frame fits on the ceiling layer and the

installation is complet

ed.In order to prevent the lift falling down,We suggest add 4pcs steel rods 

(Ø3-Ø4mm dia 

requir

ed)at the fou

rs end cor

ner,and place it in

to the ceiling as well.

Suggest to add four Ø3-Ø4mm

 steel wires to reinforce the fall

 prevention

Summary of Contents for GPAC76Series









Reviews: