Grandstream Networks WP810 Administration Manual Download

Page: 59 / 62

P a g e

WP810 Administration Guide

Version 1.0.7.83

Figure 13: WP810 Upgrade Configuration via Web GUI

Note:

Please do not power off or unplug the WP810 when the upgrading process is on.

-In case wrong firmware file is uploaded or something goes wrong, an error message will be prompt

indicating that the firmware upgrade failed.

Local Firmware Servers

Instructions for local firmware upgrade via TFTP:

1. Unzip the firmware files and put all of them in the root directory of the TFTP server.

2. Connect the PC running the TFTP server and the WP810 device to the same LAN segment.

3. Start the TFTP server and configure the TFTP

server in the phone’s web configuration interface.

4. Configure the Firmware Server Path on your WP810 to the IP address of the PC.

5. Update the changes and reboot the WP810.

Provisioning and Configuration File Download

Grandstream SIP Devices can be configured via the Web Interface as well as via a Configuration File

(binary or XML) through TFTP or HTTP/HTTPS. The "Config Server Path" is the TFTP, HTTP or HTTPS

server path for the configuration file. It needs to be set to a valid URL, either in FQDN or IP address format.

The "Config Server Path" can be the same or different from the "Firmware Server Path".

Summary of Contents for WP810































































Search results

Summary of Contents for WP810

Reviews:

Related manuals for WP810

Brands by name

Popular brands

Grandstream Networks WP810, Administration Manual

Search results

Summary of Contents for WP810

Reviews:

Related manuals for WP810

Brands by name

Popular brands