background image

5

GrandCanyonGasLogs.com 

[email protected]

STEP BY STEP INSTALLATION

This Battery Electronic control system must be installed by a qualified gas  

professional. These instructions MUST be followed to ensure proper performance 

and safety.  Failure to do so could result in serious injury or death.   

Battery electronic valve system is shipped pre-assembled with fittings and heat shields already attached.   

For systems ordered “Assembled” the valve system is pre-assembled and tested at the factory before shipping.  

Perform the installation with extreme care ensuring not to damage the valve, module or wiring harness 

connections. It is also recommended that the valve assemble is performed outside of the fireplace.  

Pre-Installation – 

For assembly of control system to an existing gas log system, ensure that all the media has been removed and 

the burner is clear of all dust and debris.  Check to ensure that the valve system and burner are labeled for the 

gas type supplied to the fireplace (Natural Gas or Propane).  Also check to ensure that the proper gas pressure 

is supplied to appliance (Minimum 5" W.C Natural Gas, Minimum 10" W.C Propane).  

This Battery Electronic Control must be installed by a qualified professional 

service technician.  Instructions must be followed carefully when installing 

to ensure proper performance.

These instructions must be used as a supplement to the instructions supplied with the Grand Canyon 

Gas Logs burner system. Follow the burner system instructions and make adjustments as appropriate 

for the addition of a battery electronic system. Use gas pipe sealing compound that is resistant to all 

gasses (or Teflon tape) and apply to all male pipe connections. DO NOT apply pipe sealing compound 

to any flare connections.  Make sure that all connections are tight.

Installation – 

Remove all burner components for the burner kit and 

the valve control system parts.  Locate the silver gas 

control valve, (2) 3/8" FIP x ½" Flare brass elbows, 

Velcro & green control module.  Using pipe sealing 

compound insert each of the brass fittings into the 

valve tightly, with the connections facing the bottom 

of the valve, Fig.1. Attach the green control  

module to the valve as shown in the picture.  

NOTE: Orient the valve so that the gas inlet is on the 

right and the gas outlet is on the left.  The gas outlet is 

on the same side as the pilot assembly connection. 

Gas In

Gas Out

Fig. 1

Summary of Contents for MVKE I KLP

















Reviews: