background image

13

GrandCanyonGasLogs.com 

[email protected]

14

Burner: 

 

Grand Canyon Gas Logs burners carry a life time warranty 

against manufacture defects or breakage as long as the appliance 

is installed inside and by a professional installer. In the event a 

defect or breakage occurs a replacement will be available for pick-

up from the dealer at which the burner was originally purchased. 

This warranty is limited to original purchaser only. Indoor burners 

installed outside carry a (1) year warranty.

Electrical and Valves:

 

Grand Canyon Gas Logs valves, remotes & receivers carry a (2) 

year warranty against breakage or defects from date of purchase, 

by original purchaser, and must be installed be a licensed profes-

sional installer. This warranty only covers use with Grand Canyon 

Gas Logs burners and logs. In the event a defect or breakage 

occurs a replacement will be available for pick-up from the dealer 

at which the burner was originally purchased. Batteries are not 

covered under this warranty. ODS pilot assemblies carry a (1) 

year warranty.

WARRANTY CARD

Warranty claim 

Purchased from (Showroom name) ___________________________________________________________________

City  _____________________________________________________________ State____________________________

Day/Month/Year ___________________________________________________________________________________

Model purchased __________________________________________________________________________________

YOUR INFORMATION

Name: ___________________________________________________________________________________________

City  _____________________________________________________________ State____________________________

Phone Number ____________________________________ Email ___________________________________________

Date of install _____________________________________________________________________________________

Copy & Mail to:

Grand Canyon Gas Logs

3515 E. Atlanta Ave., Phoenix, AZ 85040

WARRANTY

Summary of Contents for MVKE I KLP

















Reviews: