manualshive.com logo in svg

Graco ULTRA MAX 795, Instructions-Parts List Manual

Share
Download
Graco ULTRA MAX 795 Instructions-Parts List Manual Download Page 8

8

308800

Startup

10.

Adjust spray pattern.

a.

Increase pressure just until spray from gun is
completely atomized. Use lowest pressure
necessary to get desired results. This reduces
overspray and fogging, decreases tip wear and
extends the life of the sprayer.

b.

For more coverage, use larger tip  rather than
increasing pressure.

c.

Test spray pattern. To adjust pattern, engage
gun safety latch, loosen retaining nut. Position
tip guard horizontally for horizontal pattern or
vertically for vertical pattern. Then tighten
retaining nut. Fig. 5.

Fig. 4

J

L

39

G

F

E

7691A

03008

GUN SAFETY 
LATCH ENGAGED

GUN SAFETY 
LATCH  DISENGAGED

Fig. 5

RAC IV
HANDLE

RETAINING
NUT

Cleaning a Clogged Tip

WARNING

INJECTION HAZARD

To reduce the risk of serious injury,
whenever you are instructed to relieve
pressure, follow the 

Pressure Relief

Procedure

 on page 7.

1.

Relieve pressure.

2.

Clean front of tip frequently during operation.

3.

If spray tip clogs, release gun trigger, engage gun
safety latch, and rotate RAC IV handle 180

. 

See Fig. 5.

4.

Disengage gun safety latch and trigger gun into
waste container. Engage gun safety latch again.

5.

Rotate RAC IV handle 180

 to original position,

disengage gun safety latch, and resume spraying.

6.

If tip is still clogged, engage gun safety latch, shut
off and unplug the sprayer, and open pressure
drain valve to relieve pressure. Clean spray tip as
shown in manual 308644.

Summary of Contents for ULTRA MAX 795





































Reviews:

No comments

Brands by name

Popular brands

Load more brands