manualshive.com logo in svg

Graco ULTRA MAX 795, Instructions-Parts List Manual

Share
Download
Graco ULTRA MAX 795 Instructions-Parts List Manual Download Page 2

2

308800

Table of Contents

Warnings

2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Component Function and Identification

5

. . . . . . . . . . . . 

Setup

6

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Startup

7

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Shutdown and Care

9

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Flushing

10

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Troubleshooting

11

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Spin Test

17

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

General Repair Information

16

. . . . . . . . . . . . . . . . . . . . . 

Motor Brush Replacement  

18

. . . . . . . . . . . . . . . . . . . . . 

Power Supply Cord Replacement 

19

. . . . . . . . . . . . . . . 

On/Off Switch Replacement 

19

. . . . . . . . . . . . . . . . . . . . 

Pressure Control Repair 

21

. . . . . . . . . . . . . . . . . . . . . . . 

Bearing Housing & Connecting Rod Replacement

24

. 

Drive Housing Replacement

25

. . . . . . . . . . . . . . . . . . . . 

Motor Replacement

27

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Displacement Pump Repair

29

. . . . . . . . . . . . . . . . . . . . . 

Accessories

31

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Technical Data

31

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Dimensions

31

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Parts Drawing – Sprayer

32

. . . . . . . . . . . . . . . . . . . . . . . 

Parts List – Sprayer

33

. . . . . . . . . . . . . . . . . . . . . . . . . . . 

Wiring Diagram

35

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Graco Phone Number

36

. . . . . . . . . . . . . . . . . . . . . . . . . . 

Graco Warranty

36

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Symbols

Warning Symbol

WARNING

T

his symbol alerts you to the possibility of serious

injury or death if you do not follow the instructions.

Caution Symbol

CAUTION

This symbol alerts you to the possibility of damage to
or destruction of equipment if you do not follow the
instructions.

WARNING

INSTRUCTIONS

EQUIPMENT MISUSE HAZARD

Equipment misuse can cause the equipment to rupture or malfunction and result in serious injury.

This equipment is for professional use only.

Read all instruction manuals, tags, and labels before operating the equipment.

Use the equipment only for its intended purpose. If you are not sure, call your Graco distributor.

Do not alter or modify this equipment. Use only genuine Graco parts.

Check equipment daily. Repair or replace worn or damaged parts immediately.

Do not exceed the maximum working pressure of the lowest rated system component. Refer to the

Technical Data

 on page 31 for the maximum working pressure of this equipment.

Use fluids and solvents which are compatible with the equipment wetted parts. Refer to the 

Tech-

nical Data

 section of all equipment manuals. Read the fluid and solvent manufacturer’s warnings.

Do not use 1,1,1–trichloroethane, methylene chloride, other halogenated hydrocarbon solvents or
fluids containing such solvents in pressurized aluminum equipment. Such use could result in a
chemical reaction, with the possibility of explosion.

Do not use hoses to pull equipment.

Route hoses away from traffic areas, sharp edges, moving parts, and hot surfaces. Do not expose
Graco hoses to temperatures above 82

C (180

F) or below –40

C (–40

F).

Do not lift pressurized equipment.

Comply with all applicable local, state, and national fire, electrical, and safety regulations.

Summary of Contents for ULTRA MAX 795





































Reviews:

No comments

Brands by name

Popular brands

Load more brands