manualshive.com logo in svg

Graco ULTRA MAX 795, Instructions-Parts List Manual

Share
Download
Graco ULTRA MAX 795 Instructions-Parts List Manual Download Page 10

10

308800

Flushing

When to flush

Determine material to spray from column 1. Flush with
material in column 2. Then follow recommendations in
one of next three columns.

CAUTION

Do not leave water or water-based fluids in sprayer if
it could freeze. Push water out with mineral spirits.
Frozen fluid in sprayer prevents starting and may
cause serious damage.

If you are going to: 

Flush with: 

Prime with: 

Clean with: 

Store unit with:

Spray with new sprayer or
sprayer that has been
stored

Mineral spirits, then
compatible solvent
such as water or
mineral spirits

Compatible paint,
such as latex or
oil-base

Compatible solvent
such as water or
mineral spirits

Mineral spirits

Spray latex paint

Warm, soapy water,
then clean water

Latex paint

Warm soapy water,
then clean water

Mineral spirits

Spray oil paint

Mineral spirits

Oil-base paint

Mineral spirits

Mineral spirits

Change latex to oil paint

Warm, soapy water,
then clean water

Mineral spirits

Mineral spirits

Mineral spirits

Change oil to latex paint

Mineral spirits, then
soapy water, and fi-
nally, clean water

Latex

Warm, soapy water,
then clean water

Mineral spirits

Change colors, same base

Compatible solvent
such as water or
mineral spirits

How to flush

WARNING

FIRE AND EXPLOSION HAZARD

To reduce static sparking and splashing,
always remove the spray tip from the
gun, and hold a metal part of the gun

firmly to the side of a grounded metal pail when
flushing.

1.

Follow 

Pressure Relief Procedure

 on page 7.

Engage gun safety latch.

2.

Turn pressure adjusting knob (J) fully counter-
clockwise to zero pressure.

3.

Remove spray tip from gun. See Fig. 8. Remove
filter bowl, filter support and screen. Clean screen
separately and install bowl without screen or
support to flush it.

4.

Put suction tube into a grounded metal pail with
1/2 gallon of compatible solvent. Close pressure
drain valve (G).

5.

Start sprayer. See page 7. To save fluid still in
sprayer, trigger gun into another container until
next fluid appears, then trigger gun back into fluid
compatible solvent container. Circulate flushing
fluid a few minutes to thoroughly clean system.

6.

Do not run pump dry for more than 30 seconds to
avoid damaging pump packings!

7.

Follow 

Pressure Relief Procedure

 on page 7.

Engage gun safety latch.

8.

Unscrew filter bowl and reinstall clean screen.
Install bowl and hand tighten.

9.

Remove suction tube and screen and clean them
separately.

G

FILTER

BOWL

SCREEN

FILTER

SUPPORT

Fig. 8

J

7694A

Summary of Contents for ULTRA MAX 795





































Reviews:

No comments

Brands by name

Popular brands

Load more brands