background image

Installation

3A8626C

19

4. While wearing heavy gloves, firmly grasp the 

outside edge of the reel flange with both hands. 

Wind the spool the correct number of turns (see 

reference table from Step 1), rotating the reel in the 

direction shown in F

IG

. 15.

• Stop only at latching locations.

• Stop the reel where there is access to the hose 

swivel (A) (F

IG

. 16), and where the reel is securely 

latched.

5. Before installation of the hose, attach a C-clamp (D, 

F

IG

. 15) to the reel flange to prevent the reel from 

unintentionally becoming unlatched and spinning 

freely.

6. Uncoil and extend the hose.

7. Install the hose stop (C) (F

IG

. 16) to the end of the 

hose. If the hose has a warning tag (F), the hose 

stop should be installed on the same end of the 

hose as the warning tag.

NOTE: If the hose is equipped with a spring guard, this 

end must be on the same end as the hose stop.

8. Run the end of the hose (B) through the hose guide 

(G) and then to the hole (E) in the reel (F

IG

. 16).

9. Attach the hose end (B) to the hose reel swivel (A).

10. Carefully remove the C-clamp (D) (F

IG

. 15),

11. Pull on the hose hard enough to release the latch, 

and slowly allow the hose to retract.

12. Re-position the hose stop so the hose extends far 

enough for all operators to reach the dispense 

valve.

13. Flush the hose following the 

Flush the Equipment

 

instructions, page 9.

F

IG

. 15

D

F

IG

. 16

A

B

F

C

G

E

Summary of Contents for SDL23 Series























































Reviews: