background image

Warnings

WARNING

MOVING

MOVING

MOVING PARTS

PARTS

PARTS HAZARD

HAZARD

HAZARD

Moving parts can pinch or amputate fingers and other body parts.

• Keep clear of moving parts.
• Do not operate equipment with protective guards or covers removed.
• Pressurized equipment can start without warning. Before checking, moving, or servicing

equipment, follow the Pressure

Pressure

Pressure Relief

Relief

Relief Procedure

Procedure

Procedure and disconnect all power sources.

SPLATTER

SPLATTER

SPLATTER HAZARD

HAZARD

HAZARD

During blow off of platen, splatter may occur.

• Use minimum air pressure when removing platen from container.

EQUIPMENT

EQUIPMENT

EQUIPMENT MISUSE

MISUSE

MISUSE HAZARD

HAZARD

HAZARD

Misuse can cause death or serious injury.

• Do not operate the unit when fatigued or under the influence of drugs or alcohol.
• Do not exceed the maximum working pressure or temperature rating of the lowest rated

system component. See Technical

Technical

Technical Data

Data

Data in all equipment manuals.

• Use fluids and solvents that are compatible with equipment wetted parts. See Technical

Technical

Technical Data

Data

Data

in all equipment manuals. Read fluid and solvent manufacturer’s warnings. For complete
information about your material, request Safety Data Sheet (SDS) from distributor or retailer.

• Turn off all equipment and follow the Pressure

Pressure

Pressure Relief

Relief

Relief Procedure

Procedure

Procedure when equipment is not in use.

• Check equipment daily. Repair or replace worn or damaged parts immediately with genuine

manufacturer’s replacement parts only.

• Do not alter or modify equipment. Alterations or modifications may void agency approvals

and create safety hazards.

• Make sure all equipment is rated and approved for the environment in which you are using it.
• Use equipment only for its intended purpose. Call your distributor for information.
• Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces.
• Do not kink or over bend hoses or use hoses to pull equipment.
• Keep children and animals away from work area.
• Comply with all applicable safety regulations.

PERSONAL

PERSONAL

PERSONAL PROTECTIVE

PROTECTIVE

PROTECTIVE EQUIPMENT

EQUIPMENT

EQUIPMENT

Wear appropriate protective equipment when in the work area to help prevent serious injury,
including eye injury, hearing loss, inhalation of toxic fumes, and burns. Protective equipment
includes but is not limited to:

• Protective eyewear, and hearing protection.
• Respirators, protective clothing, and gloves as recommended by the fluid and solvent

manufacturer.

4

3A5400B

Tel:  866-777-6060 
Fax: 866-777-6383

Springer Pumps, LLC

Website: www.springerpumps.com 

Int'l: +001 267 404 2910

Summary of Contents for SaniForce SPU.A01AAA1AA0C21















Reviews: