Graco Reactor 2 E-30i Operation Download Page 58

Page: 58 / 94

Startup

6. Press start button

on the engine control

module twice to start the generator. Verify

voltages are displayed on engine control module

before moving to next step.
The controller will automatically begin glow plug

warming and crank operations. Allow engine to

reach full operating speed.

Note

Engine will not start if main power switch

is in the ON position.

7. Turn main power switch ON.

The ADM will display the following screen until

communication and initialization is complete.

8. For ﬁrst startup of new system, set system

settings on ADM in Setup Mode.
See

Initial System Setup, page 47

9. For ﬁrst startup of new system, adjust air settings

to zero:
a.

Close the main air shutoff valve (CK).

b. Ensure all three air regulators are turned fully

counterclockwise.

332636C

Summary of Contents for Reactor 2 E-30i































































































Search results

Summary of Contents for Reactor 2 E-30i

Reviews:

Related manuals for Reactor 2 E-30i

Brands by name

Popular brands

Graco Reactor 2 E-30i, Operation

Search results

Summary of Contents for Reactor 2 E-30i

Reviews:

Related manuals for Reactor 2 E-30i

Brands by name

Popular brands