Graco Reactor 2 E-30i Operation Download Page 54

Page: 54 / 94

Maintenance

Use this screen to view daily and lifetime cycles or

gallons that have been pumped and gallons or liters

remaining in the drums.
The lifetime value is the number of pump cycles or

gallons since the ﬁrst time the ADM was turned on.
The daily value automatically resets at midnight.
The manual value is the counter that can be manually
reset. Press

and hold to reset manual counter.

Cycles

This screen shows daily cycles and gallons that have

been sprayed for the day.
All information listed on this screen can be

downloaded on a USB ﬂash drive.

Events

This screen shows the date, time, event code, and

description of all events that have occurred on

the system. There are 10 pages, each holding 10

events. The 100 most recent events are shown. See

System Events

for event code descriptions.

All events and errors listed on this screen can be

downloaded on a USB ﬂash drive. To download logs,

see

Download Log Files, page 79

332636C

Summary of Contents for Reactor 2 E-30i































































































Search results

Summary of Contents for Reactor 2 E-30i

Reviews:

Related manuals for Reactor 2 E-30i

Brands by name

Popular brands

Graco Reactor 2 E-30i, Operation

Search results

Summary of Contents for Reactor 2 E-30i

Reviews:

Related manuals for Reactor 2 E-30i

Brands by name

Popular brands