background image

 

2

3A8824A

Contents

Related Manuals. . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Models. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

PR70

 ISO Lube Recirculation Kit  . . . . . . . . . . . 2

Mongoose

 Chemical Metering Pump . . . . . . . . 2

Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Important Isocyanate (ISO) Information. . . . . . . . . 5

Isocyanate Conditions . . . . . . . . . . . . . . . . . . . . . 5

Keep Components A and B Separate . . . . . . . . . 5

Moisture Sensitivity of Isocyanates . . . . . . . . . . . 5

Changing Materials . . . . . . . . . . . . . . . . . . . . . . . 6

Product Introduction . . . . . . . . . . . . . . . . . . . . . . . . 6

Component Identification  . . . . . . . . . . . . . . . . . . . . 7

Theory of Operation . . . . . . . . . . . . . . . . . . . . . . . . . 8

Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Recirculation Kit Installation  . . . . . . . . . . . . . . . . 9

Final Lubrication Setup . . . . . . . . . . . . . . . . . . . 11

Recycling and Disposal . . . . . . . . . . . . . . . . . . . . . 11

End of Product Life  . . . . . . . . . . . . . . . . . . . . . . 11

Parts  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

PR70 ISO Lube Recirculation Kit, 25U135, 25U137, 

25U199  . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Pump ISO Lube Low Volume, 25U138 (102) . . . 13

Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Mongoose Pump . . . . . . . . . . . . . . . . . . . . . . . . 14

Technical Specifications  . . . . . . . . . . . . . . . . . . . . 15

California Proposition 65 . . . . . . . . . . . . . . . . . . . . 15

Graco Standard Warranty  . . . . . . . . . . . . . . . . . . . 16

Related Manuals

Models

PR70

 ISO Lube Recirculation 

Kit

Mongoose

 Chemical Metering 

Pump

NOTE: 

See the appropriate 

Related Manuals

 when no 

pump is provided.

Manual in 

English

Description

312759

PR70

 and PR70v

 with Advanced Display 

Module Operation and Maintenance Manual

312760

PR70 and PR70v Two Component Liquid 

Dispensing Systems Repair - Parts Manual

312394

PR70

 and PR70v

 Feed Systems 

Instructions - Parts Manual

312761

PR70 and PR70v Integrated Heat 

Instructions - Parts Manual

3A6225

PR70

 to PR70f

 Conversion Kit 

Instructions - Parts Manual

3A4131

Mongoose

 Chemical Metering Pump 

Instructions - Parts Manual

Part

Description

Maximum Working 

Pressure

psi (MPa, bar)

25U135

PR70 ISO Lube 

Recirculation Kit - With 

230 VAC Pump

150 (1.03, 10.3)

25U137

PR70 ISO Lube 

Recirculation Kit - 

Without Pump

150 (1.03, 10.3)

25U199

PR70 ISO Lube 

Recirculation Kit - With 

120 VAC Pump

150 (1.03, 10.3)

Part Voltage

Fluid 

Section 

Material

Flow 

Gallons 

Per Day

Maximum Working 

Pressure psi (MPa, 

bar)

A21009 120 VAC PVDF

15

150 (1.03, 10.3)

A21013 230 VAC PVDF

15

150 (1.03, 10.3)

Summary of Contents for PR70 Series

















Reviews: