background image

Operation

3A4131H

9

Operation

Pressure Relief Procedure

Follow the Pressure Relief Procedure whenever 
you see this symbol.

NOTE:

 Always discharge fluid into an approved con-

tainer or location.

1.

Turn SPEED knob (H) to off and disconnect power 
cord (B).

2.

Shut off the inlet and outlet lines using shutoff 
valves (C).

3.

Slowly crack the fitting connected to the outlet check 
valve to relieve downstream fluid pressure.

Flush the Equipment

Flush with a fluid that is compatible with the fluid 
being dispensed and the equipment wetted parts.

1.

Follow the 

Pressure Relief Procedure

2.

Connect inlet fluid line (D) to the supply source of 
the flushing fluid.

3.

Connect outlet fluid line (E) to a waste container.

4.

Run the pump until the dispensed fluid is predomi-
nately flushing fluid.

5.

Follow the 

Pressure Relief Procedure

.

Prime the Pump

1.

Connect power (B) to the pump.

2.

Set the STROKE % knob (J) to 100%. (See F

IG

. 5 

on page 10.)

3.

Set the SPEED knob (H) to maximum cycles per 
second.

While pump is operating, if fluid begins moving, no fur-
ther priming is required. 

If fluid is not moving, open prime/bleed valve (4 or 104) 
approximately one turn until fluid begins to move. When 
the inlet fluid line (D) fills, close prime/bleed valve (4 or 
104). 

This equipment stays pressurized until pressure is 
manually relieved. To help prevent serious injury from 
pressurized fluid, such as splashing fluid, follow the 

Pressure Relief Procedure

 when you stop dispens-

ing and before cleaning, checking, or servicing the 
equipment.

To avoid fire and explosion, always ground equipment 
and waste container. To avoid static sparking and 
injury from splashing, always flush at the lowest pos-
sible pressure. 

NOTICE

Do not overtighten prime/bleed valve. Damage may occur.

Summary of Contents for Mongoose Series























Reviews: