Technical Data
310622C
35
Technical Data
Viton
® is a
registered trademarks of the
Co.
Santoprene
®
is a registered trademarks of the Monsanto Co.
Loctite
®
is a registered trademark of the Loctite Corporation.
*
Displacement per cycle may vary based on suction condition, discharge head, air pressure, and fluid type.
**
Noise levels measured with the pump mounted on the floor, using rubber feet. Sound power measured per
ISO Standard 9614-1.
***The pump user must verify that the construction materials meet their specific application requirements.
Maximum fluid working pressure . . . . . . . . . . . . . . . . . . . 120 psi (0.8 MPa, 8 bar)
Air pressure operating range . . . . . . . . . . . . . . . . . . . . . . 20-120 psi (0.14-0.8 MPa, 1.4-8 bar)
Maximum air consumption . . . . . . . . . . . . . . . . . . . . . . . . 175 scfm
Air consumption at 70 psi/60 gpm . . . . . . . . . . . . . . . . . . 60 scfm (see chart)
Maximum free-flow delivery . . . . . . . . . . . . . . . . . . . . . . . 150 gpm ( 570 l/min)
Maximum pump speed . . . . . . . . . . . . . . . . . . . . . . . . . . . 145 cpm
* Gallons (Liters) per cycle . . . . . . . . . . . . . . . . . . . . . . . . 1.03 (3.90)
Maximum suction lift . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Flapper 10 ft (3.5 m) wet
Ball 18 ft (5.5 m) wet
Maximum size pumpable solids . . . . . . . . . . . . . . . . . . . .
Flapper 2.5 in. (63.5 mm)
Ball 1.0 in. (25.4 mm)
** Maximum Noise Level at 100 psi, full flow . . . . . . . . . . 89 dBa
** Sound Power Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 dBa
** Noise Level at 70 psi and 50 cpm . . . . . . . . . . . . . . . . . 78 dBa
Maximum fluid operating temperature is based on the fol-
lowing maximum diaphragm, ball, and seat temperature
ratings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PTFE 220°F (104.4°C)
Santoprene® 180°F (82.2°C)
Buna-N 180°F (82.2°C)
Viton® 250°F (121.1°C)
Air inlet size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.5” npt(f)
Wetted parts
***All fluid contact materials are FDA-compliant and meet the United States Code of Federal Regulations (CFR)
Title 21, Section 177.
All fluid contact materials are FDA-compliant.
Wetted materials on all models
. . . . . . . . . . . . . . . . . . . . .
Wetted material depending on model
. . . . . . . . . . . . . . . .
316 SST, 3A Approved Buna-N (Nitrile)
316 SST,
, Santoprene®, Buna-N (Nitrile), Viton®,
3A Approved Buna-N
Note:
Santoprene® may be used only with non-fatty, non-oily foods or alcohols up to 15%.
Non-wetted external parts. . . . . . . . . . . . . . . . . . . . . . . . .
300 series stainless steel, polyester (labels), Santoprene®
(gasket), LDPE foam (gasket)
Weight
Models with stainless steel center sections . . . . . . . . . . . 145 lb. (66 kg)
PTFE
PTFE
