background image

Warnings

WARNING

WARNING

WARNING

TOXIC

TOXIC

TOXIC FLUID

FLUID

FLUID OR

OR

OR FUMES

FUMES

FUMES HAZARD

HAZARD

HAZARD

Toxic fluids or fumes can cause serious injury or death if splashed in the eyes or on skin,
inhaled, or swallowed.

• Read MSDSs to know the specific hazards of the fluids you are using.
• Route exhaust away from work area. If diaphragm ruptures, fluid may be exhausted into

the air.

• Store hazardous fluid in approved containers, and dispose of it according to applicable

guidelines.

BURN

BURN

BURN HAZARD

HAZARD

HAZARD

Equipment surfaces and fluid that’s heated can become very hot during operation. To avoid
severe burns:

• Do not touch hot fluid or equipment.

PERSONAL

PERSONAL

PERSONAL PROTECTIVE

PROTECTIVE

PROTECTIVE EQUIPMENT

EQUIPMENT

EQUIPMENT

Wear appropriate protective equipment when in the work area to help prevent serious injury,
including eye injury, hearing loss, inhalation of toxic fumes, and burns. This protective
equipment includes but is not limited to:

• Protective eyewear, and hearing protection.
• Respirators, protective clothing, and gloves as recommended by the fluid and solvent

manufacturer.

3A2888C

5

Tel:  866-777-6060 
Fax: 866-777-6383

Springer Pumps, LLC

Website: www.springerpumps.com 

Int'l: +001 267 404 2910

Summary of Contents for Husky 15120

























Reviews: