background image

Warnings

WARNING

WARNING

WARNING

ELECTRIC

ELECTRIC

ELECTRIC SHOCK

SHOCK

SHOCK HAZARD

HAZARD

HAZARD

This equipment must be grounded. Improper grounding, setup, or usage of the system
can cause electric shock.

• Turn off and disconnect power at main switch before disconnecting any cables and

before servicing or installing equipment.

• Connect only to grounded power source.
• All electrical wiring must be done by a qualified electrician and comply with all local

codes and regulations.

• Do not expose to rain. Store indoors.
• Wait five minutes before servicing after power is removed.

BURN

BURN

BURN HAZARD

HAZARD

HAZARD

Equipment surfaces and fluid that is heated can become very hot during operation. To
avoid severe burns:

• Do not touch hot fluid or equipment.

MOVING

MOVING

MOVING PARTS

PARTS

PARTS HAZARD

HAZARD

HAZARD

Moving parts can pinch, cut or amputate fingers and other body parts.

• Keep clear of moving parts.
• Do not operate equipment with protective guards or covers removed.
• Pressurized equipment can start without warning. Before checking, moving, or servicing

equipment, follow the Pressure

Pressure

Pressure Relief

Relief

Relief Procedure

Procedure

Procedure and disconnect all power sources.

SKIN

SKIN

SKIN INJECTION

INJECTION

INJECTION HAZARD

HAZARD

HAZARD

High-pressure fluid from gun, hose leaks, or ruptured components will pierce skin. This
may look like just a cut, but it is a serious injury that can result in amputation. Get

Get

Get

immediate

immediate

immediate surgical

surgical

surgical treatment.

treatment.

treatment.

• Do not spray without tip guard and trigger guard installed.
• Engage trigger lock when not spraying.
• Do not point gun at anyone or at any part of the body.
• Do not put your hand over the spray tip.
• Do not stop or deflect leaks with your hand, body, glove, or rag.
• Follow the Pressure

Pressure

Pressure Relief

Relief

Relief Procedure

Procedure

Procedure when you stop spraying and before cleaning,

checking, or servicing equipment.

• Tighten all fluid connections before operating the equipment.
• Check hoses and couplings daily. Replace worn or damaged parts immediately.

3A3165H

5

Summary of Contents for Ex35













Reviews: