background image

Troubleshooting 

20

3A3956D

Troubleshooting

Problem

Cause

Solution

Pump (B) is not running; i.e., not 
cycling, there is no lubricant output, 
pump runs slow, the control board’s 
red LED fault is illuminated, etc.

Pump (B) malfunction.

Refer to the pump manual 332514.

Lubricant is leaking from pressure 
relief.

Blockage in the line.

Check for blockage in the line. Clear 
blockage.

Pressure switch not actuated/mal-
functioning.

Check switch wiring

Replace pressure switch 

Pressure switch set too high.

Reduce system pressure

Lubricant coming out of breather (J).

Reservoir (K) overfilled because 
Auto-Fill Shut Off (S) did not shut the 
refilling line (D).

Replace the Auto-Fill Shut Off dia-
phragm (5b) and Auto-Fill Shut Off 
valve (5a). Refer to manual 332518.

Refilling pump (P) slows down or 
stalls and no output at the fill valve 
(Z).

Auto-Fill Shut Off Valve (S) has not 
reset

Relieve all refilling line (AA) pres-
sure. see page 14.

Make sure Auto-Fill Shut Off (S) pin 
is down. See F

IG

. 17, page 17.

Refilling pump (P) runs continuously 
but does not stall.

Leakage in the system

Inspect the refilling line (V) and cor-
rect any leaks.

Reservoir (K) overfilled because 
Auto-Fill Shut Off (S) did not close 
the refill line.

Replace the Auto-Fill Shut Off dia-
phragm (5b) and Auto-Fill Shut Off 
Valve (5a). Refer to manual 332518.

Summary of Contents for Dyna-Star HP 77X202



























Reviews: