background image

Operation 

8

334127D

Operation

Pressure Relief Procedure

Follow the Pressure Relief Procedure whenever 
you see this symbol.

1. Lock the gun/valve trigger safety.

2. Close all air bleed valves (required in your system) 

to shut off the air supply to the pump.

3. Unlock the gun/valve trigger safety.

4. Hold a metal part of the gun/valve firmly to the side 

of a grounded metal pail and trigger the gun/valve to 
relieve pressure.

5. Lock the gun/valve trigger safety.

6. Open the pump bleeder valve (required in your sys-

tem), having a container ready to catch the drain-
age.

7. Leave the pump bleeder valve open until you are 

ready to spray/dispense again.

If you suspect that the spray tip/nozzle or hose is com-
pletely clogged, or that pressure has not been fully 
relieved after following the steps above, very slowly 
loosen the tip retaining nut or hose end coupling and 
relieve pressure gradually, then loosen completely. 
Clear the tip/nozzle or hose.

Pump Startup, Adjustment, and 
Shutdown Instructions

These operations depend on the system you are using. 
Refer to the instructions for your system.

This equipment stays pressurized until pressure is 
manually relieved. To help prevent serious injury from 
pressurized fluid, such as skin injection, splashing 
fluid, and moving parts, follow the Pressure Relief 
Procedure when you stop dispensing and before 
cleaning, checking, or servicing the equipment.

Heated fluid can cause severe burns and can cause 
equipment surfaces to become very hot. Wear protec-
tive gloves and clothing when operating this equip-
ment in a heated system. Allow the equipment to cool 
thoroughly before servicing.

Summary of Contents for Check-Mate 800























Reviews: