background image

Repair 

10

334127D

Replace the Throat Packings

The throat packings are available as pre-assembled 
kits.

1. Relieve the pressure. See 

Pressure Relief Proce-

dure

 on page 

8

.

2. See Figure 3. Unscrew the packing nut (2) using a 

pipe wrench. Remove the o-ring (27) and washer 
(26) from the bottom of the packing housing (25) or 
from the outlet housing (3).

3. Place the flats of the packing nut (2) in a vise. 

Unscrew the packing housing (25) and discard it 
and the packings.

4. Remove the washer (24), seal (23), and back up 

washer (22) from the packing nut.

5. The throat repair kit is pre-assembled. Screw the kit 

into the packing nut (2), making sure that the 
backup washer (22), seal (23), and washer (24) are 
properly positioned on top of the packing housing 
(25) with the lips of the seal facing down. Torque the 
packing housing (25) to 225 +/- 10 ft-lb (305 +/- 14 
N•m).

6. Before installing the packing housing into the pump, 

generously lubricate the seals with the high tem-
perature grease supplied with the repair kit.

7. If necessary, use an arbor press to install the o-ring 

(27) in the packing housing (25).

8. Screw the packing nut (2) and packing housing (25) 

into the outlet housing (3). Torque to 150 +/- 30 ft-lb 
(203 +/- 41 N•m).

Pump Part No.

Throat Seal Repair Kit

24W152

24V752

24W153

24V753

24W150

24V752

24W151

24V753

F

IG

. 3: Replace Throat Packings

WLD

Torque to 225 +/- 10 ft-lbs (305 +/- 147 N•m).

Torque to 150 +/- 30 ft-lbs (203 +/- 41 N•m).

Lips of the u-cup packing must face down.

1

2

3

Summary of Contents for Check-Mate 800























Reviews: