background image

Instructions - Parts List

Base Seal 

Automatic Flow Guns

310547C

EN

Model C27130

Double air-operated with ethylene propylene o-rings

Model C27134

Double air-operated with fluoroelastomer o-rings

Model C27132

Double air-operated with spring return assist and fluoroelastomer o-rings

Model C27151

Air actuated, spring return with ethylene propylene o-rings

100 psi (0.7 MPa, 7 bar) Maximum Air Inlet Pressure
2400 psi (17 MPa, 165 bar) Maximum Working Fluid Pressure

Important Safety Instructions

Read all warnings and instructions in this 
manual. Save these instructions. 

Model C27151 / 12062 shown

Table of Contents

Warnings  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Installation   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Ground The System   . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Installation  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Operation   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Pressure Relief Procedure   . . . . . . . . . . . . . . . . . . . . . . 5

Troubleshooting  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Service   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Automatic Flow Gun Disassembly   . . . . . . . . . . . . . . . . 6
Automatic Flow Gun Reassembly  . . . . . . . . . . . . . . . . . 7

Parts   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

C27130  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
C27134  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
C27132  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
C27151  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Kits and Accessories  . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Repair Kit C27131 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Repair Kit C27133 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Technical Data   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Mounting Dimensions  . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Graco Standard Warranty  . . . . . . . . . . . . . . . . . . . . . . . . 14

Summary of Contents for C27130















Reviews: