background image

309016

Rev. B

First choice when

quality counts.

t

INSTRUCTIONS–PARTS LIST

INSTRUCTIONS

This manual contains important

warnings and information.
READ AND KEEP FOR REFERENCE.

Direct-Drive

AquaMax

t

 Pressure Washers

Model 804594, Series A
AquaMax DD6814

 pressure washer with 5.5-hp engine

and 680 liters/hr (3 gpm) pump on Hi-Boy cart with hose, gun, and tips

140 bar, 14 MPa (2000 psi) Maximum Working Pressure

Model 804597, Series A
AquaMax DD9021

 pressure washer with 11-hp engine

and 900 liters/hr (4 gpm) pump on Hi-Boy cart with hose, gun, and tips

210 bar, 21 MPa (3000 psi) Maximum Working Pressure

Model 804596, Series A
AquaMax DD9023

 pressure washer with 13-hp engine

and 900 liters/hr (4 gpm) pump on Hi-Boy cart with hose, gun, and tips

230 bar, 23 MPa (3300 psi) Maximum Working Pressure

U.S. Patent
Patented 1983, Canada 
and other patents pending

Related Manual

Spray Gun

308511

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441

E

COPYRIGHT 1999, GRACO INC.

Graco Inc. is registered to I.S. EN ISO 9001

Model 804597

9259A

Summary of Contents for AquaMax 804594 A Series























Reviews: