background image

310314

5

WARNING

MOVING PARTS HAZARD

Moving parts, such as the ram follower plate/pump inlet can pinch fingers.

D

Do not operate the equipment with the guard removed.

D

Keep clear of all moving parts when starting or operating the equipment.

D

Keep hands and fingers away from the priming piston during operation and whenever the pump
is charged with air.

D

Keep clear of the follower plate, pump fluid inlet, and lip of the fluid container when raising or
lowering the ram.

D

Before checking or servicing the ram or pump, follow the 

Pressure Relief Procedure

 on

page 11.

TOXIC FLUID HAZARD

Hazardous fluid or toxic fumes can cause serious injury or death if splashed in the eyes or on the
skin, inhaled, or swallowed.

D

Know the specific hazards of the fluid you are using.

D

Store hazardous fluid in an approved container. Dispose of hazardous fluid according to all local,
state and national guidelines.

D

Always wear protective eyewear, gloves, clothing and respirator as recommended by the fluid
and solvent manufacturer.

D

Avoid exposure to heated material fumes.

D

Provide adequate ventilation.

Summary of Contents for 970056























Reviews: