![background image](http://html1.mh-extra.com/html/graco/7980/7980_owners-manual_2252860003.webp)
9
768-3-98
Step 2.
Turn down fabric flaps to cover openings.
Step 3.
When replacing the bar, turn
back fabric flaps to expose
openings, then push arm bar
in until it locks in place.
Pull on bar to be sure both
sides are attached.
10
12
11
Step 1.
Place crotch strap between
childs legs and snap both side
buckles to the center buckle.
Adjust belt as needed to get a
snug fit around your child.
Step 2.
Push in on front of buckle to
release.
To Secure Your Child
Avoid serious injury from falling or
sliding out. Always use seat belt.
Step 1.
Fully recline the front seat.
Step 2.
Unsnap small flaps on top of
armrests.
Step 3.
Check that arrows on inside of
canopy brackets face the front
of the stroller.
Step 4.
Insert brackets through elastic,
then through holes on armrests
as shown.
Step 5.
Push both brackets down at the
same time onto stroller frame until
they snap into place. Brackets
must fit over metal bars on inside
of frame. Be sure fabric is not
caught under brackets.
Step 6.
Resnap small flaps on armrests when
front canopy is not in use.
To Install Front Canopy
(found only on some models)
Push
Push
Metal bar
To Adjust Canopies
Push or pull canopy to desired
position.
Canopy bag (on certain models)
carries a maximum of 2 pounds
(0.9 kg).
To Adjust Backs
Step 1.
Push back of seat slightly
forward while squeezing lever
as shown to unlock.
Step 2.
Adjust to desired position.
Rear seat has four positions,
front seat has three. You may
use any combination of seat
positions.
Do not pull
on this bar!
Step 3.
To return seat back to a more
upright position, push forward on
back until it snaps into desired
position. (Front seat middle
position locks for safetyunlock by
squeezing lever before pushing
into full upright position.)
Child may slip
into leg openings and strangle.
NEVER use front seat in a
reclined carriage position
unless footrest is raised to
cover the front opening and
wire is snapped into lower
notch.
NEVER use rear seat in a
reclined carriage position
unless footrest opening
behind front seat has first
been closed by snapping the
flap in six places to the back
of the front seat.
Rear seat
Back of front seat
To Install Rear Canopy
Step 1.
Fully recline the rear seat. Locate
small knobs on the inside of the
handle.
Step 2.
Hold canopy by mounting
brackets as shown. Push
brackets in slightly and align
holes in brackets with knobs
on handle. Mount brackets
onto knobs.
Step 3.
Slide brackets down to latch.
Be sure fabric is not caught
under brackets.
Step 4.
Snap canopy fabric to seat back.
Bracket
hole
Knob
Knob
Step 1.
Fully recline the rear seat.
Step 2.
Unsnap canopy fabric from stroller.
Step 3.
Slide both brackets up, then push
brackets in slightly to remove canopy.
To Remove Rear Canopy
Slide up
and
push in
To Fold Stroller
NOTE: Before folding, (1) adjust backs to upright posi-
tion; (2) fold canopy; (3) lock rear brakes; (4) align front
wheels with frame by pulling stroller slightly backward.
Step 1.
Pull up on latches on sides of
handle to fold as shown and push
handle forward slightly.
Step 2.
Push down on secondary lock on
right side of stroller as shown.
Continue pushing handle forward.
Front wheels must align so they
do not interfere with folding.
Step 3.
Lock storage latch (on inside
of handle on right side of stroller).
Align front
wheels
To Remove Arm Bar
Step 1.
Push in the tabs on both sides
of the bar as shown. Pull the
bar straight out.