background image

Repair

7. Slide the air piston (124) out of the top of the

air motor base (118). Remove o-ring (120) and

gasket (102) from inside the air motor base.

Remove o-ring (123) from groove on outside of

base. Inspect all parts, including the spring (122)

in the air motor base.
NOTE: Do not remove the spring (122) and

retainer (121) if you do not have to.
NOTE: If the white bushing (119) needs to

be replaced, use an arbor press to remove.

Alternate tapping on the edges with a hammer

and a nylon rod or metal punch also will work.

The spring (122) and retainer (121) must be

removed first.

Figure 6

Air Motor Reassembly

Cylinder threads are sharp. Always wear protective

gloves to prevent cuts.

1. If the bushing (119) was removed, use an arbor

press and seat it all the way into the air motor

base (118). Alternate tapping using a hammer

and nylon rod or metal punch also works.

2. Install the retainer (121) into the air motor base.

Tap on the retainer as needed to ensure it seats

all the way.

3. If the spring (122) was removed, put it into the air

motor base (118), with the wider end down. Use

a screwdriver to pop it into the groove.

4. Lubricate and install o-ring (120) and gasket

(102) on the inside of the motor base. Lubricate

and install o-ring (123) on the outside.

5. Use flats to clamp the base (118) into a vise.
6. Lubricate the shoulder and the bottom outside

portion of the piston (124). Then, lower it into the

air motor base (118).

3A2977K

13

Summary of Contents for 3A2977K





























Reviews: