Graco 309028ZAT Instructions Manual Download

Page: 33 / 98

Operation

309028ZAT

NOTE:

If the Pump does not prime properly, which may

occur with heavier, high viscosity fluids, increase the air
pressure with the RAM DOWN Air Regulator (AK).

NOTE:

If fluid is forced out around the top wiper, ram

pressure is too high; decrease the air pressure with the
RAM UP Air Regulator (AJ).

NOTE:

Ram pressure adjustments are carried out using

the dual REGULATOR Control Knobs (AC, AE) inside
the Pneumatic Logic Panel (G). The upper regulator
knob controls the downward pressure of the ram, and
the lower regulator knob controls the upward pressure
of the ram. See F

. 5 on page 14.

22. After closing the bleed valve, return PUMP NO. 1

and PUMP NO. 2 REGULATOR Control Knobs (AC,
AE) to the normal Pump pressure setting.

23. Open the air motor ball valves.

24. Open the ball valve in the outlet manifold from

Pump No. 1 and 2.

25. Remove the waste containers, clean up any spilled

material, and dispose of the waste material
properly.

26. Press the PUMP RESET Pushbutton to restore the

system to operation.

27. Check that the following lights are lit:

•

SYSTEM PRESSURIZED

•

AIR PRESS ON

•

RAM READY

•

PUMP READY

Daily System Startup

This procedure is normally provided by the integrator.

System Shutdown

This procedure is normally provided by the integrator.

Stopping the System

To stop the system, close the Main Air Shutoff Valve (P)
(see F

. 15) to the Supply Unit.

Restarting the System

To restart the system, perform the following steps:

1. Open the Main Air Shutoff Valve (P) to the Supply

Unit (see F

. 15).

2. At the Junction Box Panel (H), press the PUMP

RESET Pushbutton, which restarts the Pumps after
the Pumps were turned off. See F

. 6 on page 16.

. 15

Ti20917a

Summary of Contents for 309028ZAT



































































































Search results

Summary of Contents for 309028ZAT

Reviews:

Related manuals for 309028ZAT

Brands by name

Popular brands

Graco 309028ZAT, Instructions Manual

Search results

Summary of Contents for 309028ZAT

Reviews:

Related manuals for 309028ZAT

Brands by name

Popular brands