background image

Parts

3A8502A

23

Accessories

To ensure maximum pump performance, make sure all 

accessories are properly sized to meet your system 

requirements.

Air Line

Install the following accessories in the order shown in 

Typical Pump Installation

, page 10, using adapters as 

necessary.

NOTE:

 Be sure the air valves are easily accessible from 

the pump and located downstream from the air 

regulator.

Air line lubricator:

 Provides automatic air motor 

lubrication.

Air line filter (AC):

 Removes harmful dirt and 

moisture from compressed air supply.

Bleed-type air valve (AD):

 Isolates air line 

accessories for servicing. Locate upstream from all 

other air line accessories.

Fluid Line

Fluid drain valve (AE):

 Required in your system to 

relieve fluid pressure in the fluid supply lines. Install the 

drain valve so that it points down and the handle points 

up when the valve is opened.

Grounding Clamp (not included)

Bleed-Type Master Air Valve (not included)

Maximum Working Pressure: 300 psi (2.1 MPa, 21 bar)

Air Line Filter (not included)

Maximum Working Pressure: 

250 psi (1.7 MPa, 17.5 bar)

Trapped air can cause the pump to cycle 

unexpectedly, which could result in serious injury from 

splashing or moving parts.

Part

Description

Qty.

103538 CLAMP, ground

1

Part

Description

Qty.

107142 VALVE, ball, vented; 1/2 npt(m) inlet x 

1/2 npt(f) outlet

1

Part

Description

Qty.

106149 FILTER, air line; 1/2 npt(f) inlet and 

outlet

1

WLD

WLD

WLD

Summary of Contents for 26D001

































Reviews: