background image

Repair

Replace Throat Packings

Note

The throat packings are available as a

preassembled kit.

Pump Part No.

Throat Seal Repair

Kit

24W152

24V752

24W153

24V753

24W150

24V752

24W151

24V753

1. Relieve the pressure. See

Pressure Relief Procedure, page 8

.

2. See Fig. 2. Unscrew the packing nut (2) using a

pipe wrench. Remove the o-ring (27) and washer

(26) from the bottom of the packing housing (25)

or from the outlet housing (3).

3. Place the flats of the packing nut (2) in a vise.

Unscrew the packing housing (25) and discard it

and the packings. Remove the washer (24), seal

(23), and backup washer (22) from the packing

nut.

4. The throat repair kit is preassembled. Screw the

kit into the packing nut (2), making sure that the

backup washer (22), seal (23), and washer (24)

are properly positioned on top of the packing

housing (25), with the lips of the seal facing

down. Torque the packing housing (25) to 225

±10 ft-lb (305 ± 14 N•m).

5. Before installing packing housing into pump,

generously lubricate seals with high temperature

grease supplied with repair kit.

6. If necessary, use an arbor press to install o-ring

(27) in packing housing (25).

7. Screw the packing nut (2) and packing housing

(25) into the outlet housing (3). Torque to 150 ±

30 ft-lb (203 ± 41 N•m).

Figure 2 Throat Packings

1

Torque to 225 ± 10 ft-lb (305 ± 14 N•m).

2

Torque to 150 ± 30 ft-lb (203 ± 41 N•m).

3

Lips of u-cup packing must face down.

10

334127A

Summary of Contents for 24W150























Reviews: