background image

Instructions

308939D

9

Trigger Cable and Dual Gun Selector Operation

In a two-gun operation, the second gun cable 
(402) is black with a light-red cover at each 
end. Trigger from the pump side (or outside) 
position of the dual gun selector (L).

To trigger one gun

, move the selector (L) left 

or right, depending on how your cables are 
routed to the guns, until the spool (M) 
protrudes through the plate. You may need to 
move the plate (N) a little to get the spool 
through.

To trigger both guns

, center the selector (L)

Trigger cable tension adjustment 

(Fig. 6)

1

Relieve pressure, page 2.

2

Be sure the gun is properly mounted in 
holder as instructed in Step 4 under 

Mount Gun in the Gun Holder

, page 

8.

3

Pull the actuator level (94) forward and 
hold it. Lift up on the gun trigger (T) until 
there is slight resistance. Visually check 
to see if there is about 1/32 to 1/16 in/ 
(1-2 mm) gap between the trigger lever 
(H) and where the gun trigger touches 
the bar.

4

To adjust the tensions, loosen the 
screw in the block (P). Slide the block 
forward to increase the gap and 
backwards to decrease the gap. 
Tighten the screw.

5

Recheck the gap and continue 
adjusting as needed.

NOTICE

Always note to which gun and position on 

the dual gun selector (L) each of the cables 

goes so the correct gun is triggered. 

NOTICE

A loose cable prevents the gun from being 

fully triggered, which causes premature 

wear of the gun needle. A tight cable 

prevents the gun from being fully 

untriggered, which results in dripping and 

premature tip wear. Follow steps at the 

right if adjustment is needed.

NOTICE

To prevent premature wear of the cable, do 

not allow the cable (402) to rub against the 

outside edges of the slot (S) in the block 

(A). Rotate the block slightly to eliminate 

rubbing.

1

L

1

N

N

M

402

Shown in 
three positions

ti25657a

Fig. 5

94

FORWARD

402

P

R

1/32 to  1/16”
(1–2 mm)

T

H

ti25658a

Fig. 6

Summary of Contents for 241284














Reviews: