background image

Instructions 

6

308939D

Adjust Simultaneous Gun Triggering

1.

Align the front of guns by adjusting the 

gun arms. See page 7.

2.

Position the dual gun selector to trigger 

both guns. See page 9.

3.

Start the sprayer, using water, or spray 

on cardboard. Trigger the guns to see if 

the lines begin at the same time and 

place.

If one gun triggers before the other, reduce 

the cable tensions of the gun that triggers 

first. See 

Trigger cable tension adjustment

 

on page 9.
If one line starts in front of the other, adjust the 

position of the guns. See page 7.
Re-trigger the guns to check adjustments.

Positioning Gun Arm Assembly

When the guns are moved:

1.

Disengage the cables (402, H) first. See 

page 3. Pull out more of the 50 ft. (15 m) 

hose, if necessary. 

2.

After moving the guns, reposition the tip 

guard so it is parallel to the ground and 

its “wings” face the front and back of the 

unit.

To reduce the risk of fluid injection injury, always 

disengage the trigger cable to the gun(s) before 

moving or adjusting the guns or gun arms. See 

page 3. 

NOTICE

Do not kink the cables, which could prevent 

them from properly triggering and 

untriggering the guns.

B

2

1

First gun

Second gun

H

402

2

1

6

404

93

405

D

DETAIL A

PUMP SIDE

ENGINE SIDE

G

D

F

E

ti25655a

Fig. 3

Summary of Contents for 241284














Reviews: