background image

Pump Function Module System Operation 

8

310766E

Pump Function Module System Operation

Manual Pressure Relief 
Procedure

1.

Relieve system pressure to which Graco module 
supply units are attached. (See manual 308027).

2.

Close dispenser ball valves (A). Disconnect ball 
valves from system. See F

IG

. 1.

3.

Close pump air bleed valve (B).

4.

Shut off main air bleed valve (C) required in your 
system. Set ram director valve to DOWN. Ram will 
slowly drop.

5.

Open the drain valve (required in your system) 
and/or the pump bleeder valve (D). Have a container 
ready to catch the drainage.

6.

Leave the drain valve open until you are ready to 
spray/dispense again.

7.

Repeat procedure for each ram.

Always engage the trigger lock when you stop spraying 
to prevent the gun from being triggered accidentally by 
hand or if dropped or bumped.

Differential Pressure Switch

The differential pressure switch measure the fluid pres-
sure difference between the inbound and outbound side 
of the filter. The pump function module system is 
shipped from the factory with the differential pressure 
set at 100 PSI.

Adjusting the Differential Pressure

1.

Enter the set up mode by pressing button (F). Set 
point 1 (SP1) will display. See F

IG

. 2.

2.

To display the current psi value press and release 
button (E). 

The actual psi value is the number 

displayed times 10. 

See F

IG

. 3.

Automatic pressure relief is actuated by the cell 
controller.

WARNING

Follow 

Manual Pressure Relief Procedure (auto-

matic pressure relief is actuated by the cell con-
troller)

 when you stop spraying and before cleaning, 

checking, servicing, or transporting equipment. Read 
warnings, page 3. 

WARNING

Read warnings, page 3. 

F

IG

. 2

F

IG

. 3

bar

MPa

PSIX10

OUT2

OUT1

rP

1

bar

MPa

PSIX10

OUT2

OUT1

0

bar

MPa

PSIX10

OUT2

OUT1

10

bar

MPa

PSIX10

OUT2

OUT1

SP

1

E

F

bar

MPa

PSIX10

OUT2

OUT1

rP

1

bar

MPa

PSIX10

OUT2

OUT1

0

bar

MPa

PSIX10

OUT2

OUT1

10

Actual pressure is 100 psi 

(psi number displayed x 10)

E

F

Summary of Contents for 234956





















Reviews: