background image

ACCESSORIES

Accessories must be purchased separately.

Use only GENUINE GRACO PARTS AND ACCESSORIES.

WARNING

NEVER operate your equipment at a working pressure rating that is higher than the lowest rated component in
your system. Lower rated components may not be able to withstand the pressure developed by the pump and may
rupture, causing serious bodily injury or property damage.

The accessories in the box, below, are approved by Factory Mutual.

GROUNDED AIR SUPPLY HOSE
7 bar (100 psi) MAXIMUM WORKING PRESSURE
6.35 mm (0.25 in.) ID, 1/4 npsm(fbe)

220–444

1.2 m (4 ft)

218–100

5 m (15 ft)

218–101

8 m (25 ft)

218–102

11 m (36 ft)

218–103

15 m (50 ft)

220–119

23 m (75 ft)

220–120

30.5 m (100 ft)

FLUID HOSE ASSEMBLIES (Nylon)
14 bar (225 psi) MAXIMUM WORKING PRESSURE
6.35 mm (0.25 in.) ID, 3/8 npsm(fbe)

215–637

8 m (25 ft)

215–638

15 m (50 ft)

215–639

75 ft (23 m)

215–640

100 ft 30.5 m)

215–641

150 ft (46 m)

FLUID HOSE ASSEMBLIES (Nylon)
35 bar (500 psi) MAXIMUM WORKING PRESSURE
6.35 mm (0.25 in.) ID, 3/8 npsm(fbe)

216–076

8 m (25 ft)

216–077

15 m (50 ft)

216–078

23 m (75 ft)

216–079

30 m (100 ft)

216–080

46 m (150 ft)

WARNING SIGNS
Available from Graco at no extra charge.
Must be ordered separately.

180–060

Warning Sign (English)

180–061

Warning Sign (French)

180–062

Warning Sign (German)

180–063

Warning Sign (Spanish)

ACCESSORIES

The accessories below and on page 31 have not been tested by Factory Mutual.

AIR LINE ACCESSORIES

GROUNDED AIR SUPPLY HOSE
7 bar (100 psi) MAXIMUM WORKING PRESSURE
8 mm (0.315 in.) ID; 1/4 npsm(fbe); 
Color coded gray; More flexible than black hose

223–068

1.2 m (4 ft)

223–069

5 m (15 ft)

223–070

8 m (25 ft)

223–071

11 m (36 ft)

223–072

15 m (50 ft)

223–073

23 m (75 ft)

223–074

30.5 m (100 ft)

QUICK DISCONNECT COUPLING ASSY. 110–806
Includes a quick disconnect coupling insert, which
replaces air inlet fitting 179–400, and a shut-off coupling
body (left hand thread), which connects to the grounded
air hose.

AIR HOSE ADAPTER 185–493
For connecting two or more air supply hoses together.
1/4 npt(m) x 1/4 npsm(m) left–hand thread.

HIGH VOLUME AIR REGULATOR 206–199
0–9 bar (0–125 psi) Regulated Pressure
14 bar (200 psi) Steel Pressure Gauge
1/2 npt(f) inlet and outlet

AIR FILTER & MOISTURE SEPARATOR 106–148
17.5 bar (250 psi) MAXIMUM WORKING PRESSURE
For cleaning and drying air in air spray system. 
20 micron element, 5 oz. bowl capacity, 
3/8 npt(f) inlet and outlet

Summary of Contents for 218-026

































Reviews: