background image

307552

3

 

WARNING

TOXIC FLUID HAZARD

Hazardous fluid or toxic fumes can cause serious injury or death if splashed in the eyes or on the skin, 
inhaled, or swallowed.

Know the specific hazards of the fluid you are using.

Store hazardous fluid in an approved container. Dispose of hazardous fluid according to all local, state and 
national guidelines.

Any additives to the air supply, such as oil or anti–freeze will be exhausted into the atmosphere.

Always wear protective eyewear, gloves, clothing and respirator as recommended by the fluid and solvent 
manufacturer.

FIRE AND EXPLOSION HAZARD

Improper grounding, poor ventilation, open flames or sparks can cause a hazardous condition and result 
in a fire or explosion and serious injury.

Ground the equipment. Refer to 

Grounding

 on page 5.

If there is any static sparking or you feel an electric shock while using this equipment, 

stop pumping 

immediately.

 Do not use the equipment until you identify and correct the problem.

Provide fresh air ventilation to avoid the buildup of flammable fumes from solvents or the fluid being sprayed.

Keep the work area free of debris, including solvent, rags, and gasoline.

Electrically disconnect all equipment in the work area.

Extinguish all open flames or pilot lights in the work area.

Do not smoke in the work area.

Do not turn on or off any light switch in the work area while operating or if fumes are present.

Do not operate a gasoline engine in the work area.

MOVING PARTS HAZARD

Moving parts can pinch or amputate your fingers.

Keep clear of all moving parts when starting or operating the pump.

Before servicing the equipment, follow the 

Pressure Relief Procedure

 on page 7 to prevent the equipment 

from starting accidentally.

Summary of Contents for 217-381

















Reviews: