background image

22

308-560

Pressure Control Replacement

WARNING

FLUID INJECTION HAZARD

To reduce the risk of serious injury,

follow the illustrated 

Pressure Relief

Procedure 

warning on page 12 when-

ever you are instructed to relieve pressure.

1. Relieve pressure.

2. Disconnect the filter/drain valve assembly and the

pump supply hose at the pressure control while

holding the pressure control fitting (A) firmly. See

the 

CAUTION

, below. See Fig. 17.

Do not allow the fittings (A) to turn when removing

or connecting the hose and filter/drain assembly.

Do not over tighten the screws when attaching the

pressure control board/cover. Turning the fittings or

over tightening the screws may shift the calibration

of the pressure control.

CAUTION

3. Remove the four mounting screws and washers

(302, 303, 304) from the pressure control board/

cover (301).  See Fig. 18.

4. Carefully remove the pressure control board/cover

(301) so as not to stress the cables.

5. Remove the potentiometer cable (310) from the

pressure control board/cover (301).

6. Disconnect the pressure control board/cover

black/white M+ and black M– leads from the motor

+ and– leads.

7. Disconnect the red motor leads from the TS leads

on the pressure control board/cover (301).

8. Disconnect the brown power lead (L1) from the

filter board.

9. Disconnect the blue lead (L2) from the filter board.

10. Loosen the ground terminal screw (317) and

disconnect the ground lead (C).

11. Pull off the pressure control board/cover.

04792

Fig. 17

301

TO GUN

FILTER/DRAIN

VALVE ASSEMBLY

A

A

TO PUMP

Summary of Contents for ULTRA PLUS+ 1000 231-350 A Series









































Reviews: