manualshive.com logo in svg

Gow-Mac 400 Series, Operating Manual

Share
Download
Gow-Mac 400 Series Operating Manual Download Page 30

GOW-MAC Instrument Co.           Series 400 / 402 Gas Chromatograph Operating Manual

May 2017, Rev. 7

30

 

WARNING

!

 

IT IS MOST IMPORTANT THAT ELECTRICAL POWER BE
TURNED OFF BEFORE THE HELIUM IS TURNED OFF. AS
LONG AS THE CELL AND FILAMENTS ARE HOT, THE 
HELIUM SHOULD BE FLOWING THOUGH THE DETECTOR. 
THE FLOW RATE CAN BE REDUCED TO CONSERVE HELIUM.

4.9  Daily Setup Check List

 

It is good practice to check the following items at the beginning of each day or shift, and when 
starting up the GC after a weekend shutdown.

 

A.  Electrical

 

 

_____  Additional instrumentation is connect properly.

 

B.  Pneumatic

 

 

_____  Gas cylinder pressure is suffi  cient.

 

 

_____  Cylinder pressure regulator set properly.

 

 

_____  Gas fl ow rates are adjusted properly.

 

 

_____  Appropriate columns are installed.

 

 

_____  Leak check.

 

C.  Front Panel

 

 

_____   All temperature setting controls are set BELOW the recommended circuitry
 

 

maximum limits (Chart 4-1).

 

 

_____   Recording device zeroed.

 

 

_____ 

  Detector fi laments are 

ON (

CARRIER GAS MUST BE FLOWING THROUGH

 

 

BOTH SIDES OF THE DETECTOR

).

Summary of Contents for 400 Series

































































Reviews:

No comments

Brands by name

Popular brands

Load more brands