Gow-Mac 400 Series Operating Manual Download Page 26

Page: 26 / 64

GOW-MAC Instrument Co. Series 400 / 402 Gas Chromatograph Operating Manual

May 2017, Rev. 7

A. Gas Flow

IMPORTANT

Inert carrier gas

MUST

be ﬂ owing through

both columns A and B as well

as sides A & B

of the TC detector.

THIS IS EXTREMELY IMPORTANT and

NECESSARY to preserve the ﬁ laments!

Failure to set ﬂ ow rates on both sides causes oxidation and destruction of the
ﬁ laments in the presence of oxygen.

1. Make sure that

ALL

switches are in the

OFF

position.

2. Set helium (or other carrier gas) pressure regulator to 40 psig. A minimum of 20 psig

is necessary.

3. Adjust carrier gas to: 30 mL/min. for 1/8" columns

60 mL/min. for 1/4" columns

4. Check for leaks as described in Chapter 3.

5. Disconnect ﬂ owmeter.

6. Allow 5 minutes to purge the system before turning power

B. Temperature Controls

NOTE

TEMPERATURE CONTROL KNOBS are locking type.
Push locking ring "IN" to turn knob.

ALL

switches should be in the

OFF

position.

2. Turn

DETECTOR CURRENT CONTROL

fully counterclockwise (CCW).

THIS STEP

IS EXTREMELY IMPORTANT!

3. Plug in the GC to the appropriate ac outlet. Switch the instrument ON

(HELIUM MUST

BE FLOWING!).

4. Set

INJECTION TEMPERATURE CONTROL

to desired setting.

5. Set

COLUMN TEMPERATURE CONTROL

to desired setting.

6. Set

DETECTOR TEMPERATURE CONTROL

to desired setting.

Chart 4-1 illustrates the maximum currents for cell temperatures and carrier gases

helium, nitrogen, and argon.

Summary of Contents for 400 Series

































































Search results

Summary of Contents for 400 Series

Reviews:

Brands by name

Popular brands

Gow-Mac 400 Series, Operating Manual

Search results

Summary of Contents for 400 Series

Reviews:

Brands by name

Popular brands