Gossen MetraWatt SECUTEST SI+ Operating Instructions Manual Download Page 20 | Manualshive

Page: 20 / 26

Gossen MetraWatt SECUTEST SI+ Operating Instructions Manual Download Page 20

20

GMC-I Messtechnik GmbH

7

Operation with Barcode Reader

The barcode reader B3261 and Z720A (each as accessory) allow for
all information available in barcode form to be quickly, easily and
safely entered into the test reports. This type of data entry permits
time-saving and low-cost acquisition of large amounts of information,
e.g. for series measurements of devices provided with barcodes.

7.1

Connecting the Barcode Reader

Ð

Connect the reader to the RS232 interface of the SI module.
An SI LCD window must not be active!
The barcode reader confirms the correct connection with a double
acoustic signal.

7.2

Configuring the Barcode Reader

The barcode reader B3261 and Z720A are configured for the following
barcodes:

CODE 39 / CODE 128 / EAN13 (12 digits) *

The barcode reader are immediately ready for operation when con-
nected to a SECUTEST... or

SECU

TEST

SI+

test instrument.

For operation with PROFITEST 204, the barcode reader has to be
configured with the code indicated in the operating instructions of the
barcode reader adapter. For these test instruments, only Code 128 is
possible.

If you wish to use other codes for the SECUTEST..., please consult our
Product Support Hotline, see chapter 13, page 26

* Z720A has the appropriate scanning width to be programmed to the EAN 128

barcode.

«
...
18
19
20
21
22
...
»

Summary of Contents for SECUTEST SI+



























Reviews:

No comments