manualshive.com logo in svg

Gossen MetraWatt ECUTEST ST BASE, Condensed Operating Instructions, Page: 32 / 56

Share
Download
Gossen MetraWatt ECUTEST ST BASE Condensed Operating Instructions Download Page 32

SECU

TEST ST 

B

ASE

(

10

) / 

P

RO

 

and SECU

LIFE ST 

BASE

(25)

32

Gossen Metrawatt GmbH

13.8 IE – Device Leakage Current

1

Connection also via AT16DI/AT32DI (only sensible with differential 
method)

2

Measurement must be performed with mains polarity in both direc-
tions. The largest value is documented.

Before conducting any leakage current measure-
ments, make sure that the “Ref. voltage L-PE” and 
“Alt. Test Freq.” measurement parameters have been 
set correctly in SETUP (see section 12.4).

➭

Connect the DUT to the test socket.

➭

Contact accessible, conductive parts 
which are not connected to the protec-
tive conductor with test probe P1.

➭

For DUTs with applied parts: Additionally 
contact the short-circuited inputs for the 
applied parts with test probe P1.

 

Measuring 
Parameter

Meaning

Measurement type 

Direct

Direct measuring method (via test 
socket

1

), optional probe contact

Differential

Differential current measurement
(via test socket)

Alternative

Equivalent leakage current mea-
suring method with probe contact 
(via test socket, AT16DI/AT32DI)

AT3 adapter

Only test instruments with feature 
I01: Measurement with AT3-IIIE, 
AT3-IIS or AT3-II S32 adapter
See section 13.19

Clamp

Only test instruments with feature 
I01: See section 13.18

Polarity

2

 – only with measurement type 

direct, differential and AT3 adapter

Normal 

Selection of polarity for mains 
voltage to the test socket

Reversed

Select measuring function

1

IE

Select parameters

2

Set parameters

3

Connect the DUT

4

Direct / Diff / Alt 

P1

Start test

5

Acknowledge line voltage warning

6

!

Direct & differential & AT3 adapter:

Save measured values to clipboard

7

Stop test

8

Save measurements under ID no.

9

Summary of Contents for ECUTEST ST BASE

























































Reviews:

No comments