Gossen MetraWatt ECUTEST ST BASE Condensed Operating Instructions Download Page 34

Page: 34 / 56

SECU

TEST ST

ASE

(

) /

and SECU

LIFE ST

BASE

(25)

Gossen Metrawatt GmbH

13.10 IP – Patient Leakage Current

Connection also via AT16DI/AT32DI (only sensible with differential
method)

Before conducting any leakage current measure-
ments, make sure that the “Ref. voltage L-PE” and
“Alt. Test Freq.” measurement parameters have been
set correctly in SETUP (see section 12.4).

➭

Connect the DUT to the test socket.

➭

Contact the short-circuited inputs for the
applied parts with test probe P1.

Meas. Parameter

Meaning

Measurement type

Direct P1

Direct measuring method
(via test socket) with test probe P1

Perm. connection P1

Permanently installed DUT

Single fault (SFC) – only with measurement type
direct P1

Normal status

Single fault simulation not active

N interrupted

Fault simulation active – only
phase and protective conductor
are connected to the DUT

PE interrupted

Fault simulation active – the pro-
tective conductor is disconnected
from the DUT for the duration of
the measurement.

U low to APP

Fault simulation active – low volt-
age to applied part

Polarity – only with measurement type
direct, differential and AT3 adapter

Normal

Selection of polarity for mains
voltage to the test socket

Reversed

Select measuring function

Select parameters

Set parameters

Connect the DUT

Direct P1 /

PC 1 device under test

Start test

Acknowledge line voltage warning

Direct:

Save measured values to clipboard

Stop test

Save measurements under ID no.

Summary of Contents for ECUTEST ST BASE

























































Search results

Summary of Contents for ECUTEST ST BASE

Reviews:

Related manuals for ECUTEST ST BASE

Brands by name

Popular brands

Gossen MetraWatt ECUTEST ST BASE, Condensed Operating Instructions

Search results

Summary of Contents for ECUTEST ST BASE

Reviews:

Related manuals for ECUTEST ST BASE

Brands by name

Popular brands