manualshive.com logo in svg

Gossen MetraWatt ECUTEST ST BASE, Condensed Operating Instructions, Page: 43 / 56

Share
Download
Gossen MetraWatt ECUTEST ST BASE Condensed Operating Instructions Download Page 43

Gossen Metrawatt GmbH

43

SECU

TEST ST 

B

ASE

(

10

) / 

P

RO

 

and SECU

LIFE ST 

BASE

(25)

13.19 Measurements with Test Adapter 

1

Differential current method only with test instruments 
including feature I01 (e.g. SECUTEST ST PRO)

2

Alternatively AT3-IIS or AT3-II S32 for IPE and IE

Attention!

!

Please read and observe the operating 
instructions for the test adapters regard-

ing correct connection of the test 
adapter and the DUT, as well as pecu-
liarities involved in the test procedure.

Connection Example with EL1 

Connection Example with VL2E 

Connection Example for Measuring Protective Con-
ductor Current IPE

1

 (direct method) with AT3-IIIE 

Connection Example for Measuring Device Leak-
age Current IG

1

 (differential current method) with 

AT3-IIIE 

1

Only with feature I01(e.g. SECUTEST ST PRO or SECULIFE ST BASE(25)) 

Test with Adapter

EL1

VL2E AT3-

IIIE

2

AT16DI
AT32DI

CEE 
adapter

Connectors for the DUT

Non-heating devices, 
1P+N+PE 16 A 

 —

✔

✔

 

—

 

—

Earthing contact, 
1P+N+ PE 16 A

 —

✔

 

—

 

—

 

—

CEE, 1P+N+PE 16 A

 —

✔

✔

 —

✔

CEE, 3P+N+PE 16 A

 —

✔

✔

✔

 / —

✔

CEE, 3P+N+PE 32 A

 —

✔

✔

— / 

✔

✔

5 x 4mm sockets

—

—

—

—

✔

Connectors for the test instrument

Earthing contact, 
1P+N+ PE 16 A

—

—

✔

✔

—

Socket for test probe

—

✔

✔

—

—

Plug for V–COM

1

—

—

✔

—

—

Active test

Protective conductor current 

IPE

– Direct method

—

—

✔

✔

—

– Differential current

—

—

✔

1

✔

—

Device leakage current 

IE

– Direct method

—

—

✔

✔

—

– Differential current

—

—

✔

1

✔

—

Touch current

 T

—

—

✔

✔

—

Passive test

Pro. con. resistance 

RPE

✔

✔

✔

✔

✔

Insulation resistance 

RINS

✔

✔

✔

✔

✔

Protective conductor cur-
rent 

IPE

 (equivalent leak-

age current method)

—

✔

✔

✔

✔

Extension cords: 

the following measurements, in addition to RPE 

& RINS, are performed in switch position 

EL1

Single-phase (3-pole)

✔

✔

✔

—

—

3-phase (5-pole)

—

✔

✔

—

—

Wire short-circuit

✔

✔

✔

—

—

Wire break

✔

✔

✔

—

—

Reversed wires

—

✔

✔

—

—

EL1 Adapter

P1

V

COM

P1

Summary of Contents for ECUTEST ST BASE

























































Reviews:

No comments