Gorilla Playsets Blue Ridge Mountaineer 2009 Assembly Manual Download Page 67

Page: 67 / 92

2 X 4 X 15"

AND 2)

VERTICAL SUPPORT

SUPPORT

PICNIC TABLE

COMPLETE THIS STEP

FIRST. (SEE SUB-STEPS 1

2 X 4 X 15"

PICNIC TABLE

2-1/2" WOOD SCREW

ROCK WALL REMOVED FOR ASSEMBLY CLARIFICATION

STEP 39: PICNIC TABLE

2 X 4 X 15"

PICNIC TABLE

SUPPORT

2 X 4 X 30"

PICNIC TABLE

VERTICAL SUPPORT

1: PLACE THE 2 X 4 X 15" PICNIC TABLE SUPPORT ON TOP OF THE 2 X 4 X 30" PICNIC TABLE VERTICAL SUPPORT AND

POSITION THE BOARDS AT A RIGHT ANGLE.

2: ENSURE THAT THE PICNIC TABLE SUPPORT AND THE PICNIC TABLE VERTICAL SUPPORT ARE SQUARE AND FASTEN

THE PICNIC TABLE SUPPORT TO THE VERTICAL SUPPORT WITH THREE 2 1/2" WOOD SCREWS IN THE PATTERN SHOWN

BELOW. MAKE SURE TO ASSEMBLE THE THE PICNIC TABLE SUPPORT AND THE PICNIC TABLE VERTICAL SUPPORT TO

ACCOMODATE OPPOSITE SIDES OF THE PICNIC TABLE. MAKE SURE THE ASSEMBLY IS SQUARE BEFORE PROCEEDING

TO THE NEXT STEP.

3: MEASURE OUT 15" ON THE SANDBOX BOARDS FROM THE OUTSIDE OF THE CORNER POSTS TO ENSURE THAT THE

ASSEMBLY IS SQUARE.

4: FASTEN THE ASSEMBLY CREATED FROM THE PREVIOUS TWO STEPS TO THE CORNER POST. POSITION THE ASSEMBLY

SO THAT THE PICNIC TABLE SUPPORT IS ON THE OUTSIDE OF THE CORNER POST, AND THE VERTICAL SUPPORT IS ON

THE INSIDE OF THE 2 X 6. FASTEN THE ASSEMBLY TO THE UNIT WITH THREE 2" WOOD SCREWS IN THE PICNIC TABLE

SUPPORT, AND TWO 2-1/2" WOOD SCREWS IN THE 2 X 6 AT THE BOTTOM. (SEE PATTERN BELOW)

Summary of Contents for Blue Ridge Mountaineer 2009





























































































Search results

Summary of Contents for Blue Ridge Mountaineer 2009

Reviews:

Related manuals for Blue Ridge Mountaineer 2009

Brands by name

Popular brands

Gorilla Playsets Blue Ridge Mountaineer 2009, Assembly Manual

Search results

Summary of Contents for Blue Ridge Mountaineer 2009

Reviews:

Related manuals for Blue Ridge Mountaineer 2009

Brands by name

Popular brands