Gorilla Playsets Blue Ridge Mountaineer 2009 Assembly Manual Download Page 64

Page: 64 / 92

5/4 X 2 X 16"

LARGE RAY

SMALL RAY

5/4 X 2 X 10"

1-1/2" WOOD SCREW

1: PREDRILL HOLES IN ALL RAYS WITH A 1/8" DRILL BIT AT 3/4" ON CENTER.

2: CENTER THE 5/4 X 2 X 16" LARGE RAY ONTO THE HALF SUN AND THE ROOF SUPPORT BOARDS AND FASTEN WITH

TWO 1-1/2" SCREWS.

3: EQUALLY SPACE THE SMALL RAYS ABOUT THE HALF SUN (THREE ON EACH SIDE OF LARGE RAY) AND MARK THE

POSITION OF THE SMALL SUNRAYS WITH A PENCIL.

4: SECURE THE SMALL SUNRAYS ONE AT A TIME TO THE HALF SUN AND THE ROOF SUPPORT BEAMS AND LINE THEM UP

WITH THE MARK DRAWN. FASTEN THE SMALL SUNRAYS WITH TWO 1-1/2" WOOD SCREWS EACH. REPEAT ON OTHER

SIDE OF FORT.

NOTE:

ROOF BOARDS REMOVED FROM VIEW FOR CLARITY

STEP 36: SUNBURST

Summary of Contents for Blue Ridge Mountaineer 2009





























































































Search results

Summary of Contents for Blue Ridge Mountaineer 2009

Reviews:

Related manuals for Blue Ridge Mountaineer 2009

Brands by name

Popular brands

Gorilla Playsets Blue Ridge Mountaineer 2009, Assembly Manual

Search results

Summary of Contents for Blue Ridge Mountaineer 2009

Reviews:

Related manuals for Blue Ridge Mountaineer 2009

Brands by name

Popular brands