manualshive.com logo in svg

Gorilla Playsets 1500GW, Manual, Page: 78 / 150

Share
Download
Gorilla Playsets 1500GW Manual Download Page 78

1: PLACE THE 4 X 4 X 23-1/2" SLIDE BLOCK AGAINST THE UPPER DECK SUPPORT ON THE LEFT SIDE 

(LADDER SIDE) OF THE PLAY SET. THE TOP OF THE BLOCK SHOULD BE FLUSH TO THE TOP OF THE DECK 

SUPPORT. THE BLOCK FITS BETWEEN THE LAG POST AND THE REAR CORNER POST.

2: HAVE AN ASSISTANT HOLD THE BOARD IN POSITION OR USE A CLAMP TO HOLD THE BOARD FIRMLY 

TO THE DECK SUPPORT. USE THE HOLES IN THE SLIDE BLOCK AS A TEMPLATE TO DRILL 3/8" HOLES 

THROUGH THE DECK SUPPORT.

3: HAMMER T-NUTS INTO THE HOLES ON THE INSIDE FACE OF THE DECK SUPPORT. ATTACH THE SLIDE 

BLOCK TO THE DECK SUPPORT WITH 5/16" X 4-1/2" HEX BOLTS AND 5/16" WASHERS.

STEP 26: ATTACHING SLIDE BLOCK

SLIDE BLOCK

4 X 4 X 23-1/2"

REAR OF FORT

B

DECK SUPPORT 

T-NUT

4 X 4 X 23-1/2"

SLIDE BLOCK

3/8" HOLE

SLIDE BLOCK

DETAIL B 

4 X 4 X 23-1/2"

DECK

 SUPPORT

5/16" WASHER

5/16 X 4-1/2"

HEX BOLT

70

Summary of Contents for 1500GW























































































































































Reviews:

No comments